I lager hos oss 1 enhet redo att skickas från vårt eget lager — köp nu eller be oss om ett volympris.

EA Elektro-Automatik Lägg ett bud

EA-PS-7032-10A

EA Elektro-Automatik EA-PS 7032-10A Laboratory DC Power Supply, 0-32 V / 0-10 A, 320 W, analogue interface

Kategori Other Power Supplies, UPS & Energy

Enhet: pcs

Art.nr (normaliserat): EAPS703210A

I lager 1 (Begagnad)

Lägg ett bud

1 enhet i lager

Föreslå ditt eget pris för den här artikeln — vi svarar här.

Bud och priser är inte bindande förrän en beställning har lagts och bekräftats.

Tillgängliga enheter (1)

Om EA-PS-7032-10A

The EA-PS 7032-10A is a single-output laboratory DC power supply from EA Elektro-Automatik's PS 7000 A series, rated 0-32 V and 0-10 A.

The design uses a thyristor pre-regulator followed by a linear transistor stage, which keeps ripple very low. It has a temperature-controlled fan. Voltage and current are each set with coarse and fine knobs. The supply works as a constant-voltage source with current limiting or as a constant-current source with voltage limiting, and CV and CC LEDs show which mode is active. Analogue voltmeter and ammeter are fitted (illuminated LCD meters were an option). Over-voltage protection is standard: when the set level is exceeded, a thyristor short-circuits the output in under 1 ms.

A 15-pin Sub-D socket on the front panel accepts 0-10 V signals to program voltage and current and provides 0-10 V monitor outputs, selected with the internal/external mode switch. Remote sense is supported. Several units can be connected in series or in parallel. It is used in test systems, schools, universities and laboratories.

Vanliga frågor

Can the EA-PS 7032-10A be controlled remotely?

Yes, through its analogue interface. A 15-pin Sub-D socket on the front accepts 0-10 V signals to set voltage and current and gives 0-10 V monitor outputs. There is no digital (USB/GPIB) interface.

Can two units be combined?

Yes. EA states that two or more units can be run in series or in parallel for higher voltage or current; in series the output may not exceed 500 V to ground.

Does it have over-voltage protection?

Yes. OVP is standard and adjustable from 3 V to 35 V; when it trips, a thyristor short-circuits the output in under 1 ms.

What is the difference from the EA-PS 7032-20A?

Both cover 0-32 V. The -10A model delivers up to 10 A (320 W) and the -20A model up to 20 A (640 W).

Dokument

PS 7000 A laboratory power supplies, catalogue pages (EA Elektro-Automatik, hosted by SG Labs)
Broschyr · English · www.sglabs.it

Specifikationer

Meters	Analogue V and A, class 2.0 (illuminated 3½-digit LCD optional)
Settings	Voltage and current, coarse and fine each
Regulation	Thyristor pre-regulation with linear transistor regulator; temperature-controlled fan
Mains input	230 V or 115 V ±10%, 50/60 Hz
Output power	320 W
Article number	34100306
Current ripple	<3.5 mA rms
Output current	0-10 A
Output voltage	0-32 V
Voltage ripple	<0.3 mV rms
Analogue interface	15-pin Sub-D: 0-10 V programming of V and I, 0-10 V monitor outputs
Over voltage protection	Crowbar, adjustable 3-35 V, trips in <1 ms
Regulation time (80 100% load)	80 µs
Voltage stability (0 100% load)	<25 mV
Voltage stability (±10% mains)	<3 mV